Lightspeed pos system contacy update#

Update each of the Production Printer Settings fields:.One by one, select Test Print for each of your printers to confirm that the details you have entered are correct. Repeat steps 5 - 8 for each of your secondary printers. Enter the new IP address (ending in 201, 202, 203, and so on) of the secondary printer that you set up in Configure the IP addresses of your secondary (non-intelligent) printers.Select the model of your non-intelligent printer to be registered from the dropdown menu (i.e TM-T82 or TM-T20).Fill in the Device ID field with a name for the secondary printer (e.g.Under the Device Admin heading, go to Printer.Log into the Printer Configuration page by following steps 1-4 from Configure the IP addresses of your intelligent printer.Change the last three digits of the IP Address to 201 (for the first secondary printer), 202 (for the second secondary printer), 203 (for the third secondary printer), and so onĬonnect the intelligent printer to the secondary printers.

Lightspeed pos system contacy manual#

Change Get IP Address from Auto to Manual

You will see the TCP/IP Settings menu.

You will be taken to the WebConfig page.

In the address bar, type in the IP address from one of your non-intelligent printers.

This device should be connected to the same network as the printers This must be done for all secondary printers. If this happens you will need to read our guide on Enabling DHCP for your printer.Ĭonfigure the IP addresses of your secondary (non-intelligent) printers WARNING: Holding the pen in for more than five seconds will factory reset the printer. Now press the status button using your pen, double-check that the IP address has updated and is now one and the same as the IP address that you just changed it to, and check that TCP/IP Status, Acquiring: Manual (see below). This will prompt the Printer to restart and apply these changes - it will take less than one minute or two to complete this process.

Change the last three digits of the IP Address to 200 (e.g 192.168.1.

From the System Settings for TCP/IP, change Get IP Address from Auto to Manual.

If you open TCP/IP under Wired which is under System Settings BUT cannot edit the fields, it means you have gone to the wrong page. Go to System Settings for TCP/IP which you can find by going to System Settings > Network > Wired > TCP/IP.

You will be taken to a configuration page.

For new Epson printers enter the login details:.

( Note: The TM-T88VI uses ' /webconfig-i' instead) If nothing happens, to this address, add “ /PrinterConfigurationPage ” e.g.

In the address bar, type in the IP address of your intelligent printer.

This device needs to be connected to the same network as the printers. IMPORTANT: If any of your printers printed this IP Address: 192.168.192.168 or if your DHCP says disabled, please go to the enabling DHCP guide before continuing.Ĭonfigure the IP addresses of your intelligent printer If this happens you will need to read our guide on Enabling DHCP for your printer

If you don’t get the IP address automatically, grab a pen and hold in the status button at the back of the printer for three to four seconds - BUT no more than 5 seconds. New intelligent printers, once turned on, should print an IP address automatically.IP addresses are the unique identifier for each device on a network. You will see the dialogue 'Great we found some printers!', this is confirmation that the printer has been connected to POS via Bluetooth.

The system will search for your printer.

Select the three-bar menu on the left-hand side.

Hit POS from Back Office to head over to your POS.

Under the Production Printer Settings, select the Production Printing Method: Lightspeed App.

Lightspeed pos system contacy Bluetooth#

The Bluetooth light on the printer will stop flashing once it is paired successfully and will become a solid blue light. The name of your printer should look like TM -m30_000000 Under the list of Other Devices, select your printer.Turn the Bluetooth off and then on again.On your device, go to Settings and then Bluetooth.The blue Bluetooth status light will flash once when the printer is connected to the power, this indicates it is in pairing mode.